Marine
A hull breach does not wait for a work order. Damage control shoring, box patches, leak sealing, shipboard thermal, hard-line communication and deck rigging—stocked for vessels of all sizes, from motor yachts and cruise ships to naval vessels and oil tankers. When the water comes in, be ready to keep it out.
The kit is the plan.
TEAM damage control shoring is a threaded shaft and locking collar system built for one job: holding a patched hull and a strained bulkhead until you reach port. Five kits cover everything from a motor yacht to a cruise ship, and every component in every kit interlocks with the rest.
- Five component classes: shores, extensions, bases, braces, connectors
- Every kit includes a 12, 18 and 24 inch box patch set
- Zone your vessel with a cache in each zone, so no locker is far away
The five kit options
Every kit also carries rubber feet and pads, rail, corner and angle ends, carrying straps, shoring hammers, support ledges and a full 12, 18 and 24 inch box patch set.
Planning your lockers
If you fail to plan, you plan to fail. We recommend more than one cache of equipment: divide the vessel into zones with a kit in each zone, so the gear is never on the wrong side of a closed watertight door.
Your vessel class, number of DC lockers, and any flag-state or class requirements we should design to.
Kits are built based on the size of the ship.
Don't give up the ship.
A breach from a grounding, a collision or a submerged object has to be contained fast, before flooding spirals past what the pumps can handle. The TEAM Splinter Box Patch is built to take the bulk of the ingress, ideally 80 percent or more, and hand the rest to your bilge pumps.
- Lightweight aircraft-grade aluminum
- Marine-grade white powder coat with blue reflective lettering
- Closed-cell rubber gasket seals against an irregular hull
Box Patch Size Options
How it is meant to work
The TEAM DC Box Patch is designed to contain the majority of water ingress—not stop it completely. By slowing the flooding and allowing your bilge pumps to manage the remainder, it buys valuable time to reach port. Back it with a MARQRBAG quick response grab-and-go bag beside it.
Buy your pumps time.
A patch holds because something holds the patch, and a shifted load stays put because something made it. Paratech shoring takes the strain off a temporary seal, and heavy lifting air bags put the power of a crane in the palm of your hand.
- Threaded shores, extensions, bases and braces in one interlocking system
- Air bags lift, move or shift several tons on compressed air
- Rated, repeatable and trainable
Paratech shoring
Fast, easy to deploy, and built for the harsh marine environment. Paratech Shoring includes shores, extensions, bases, braces, and connectors—all cross-compatible with the 20TDC kits.
Heavy lifting air bags
The lifting power of a crane or forklift in the palm of your hand. Paratech Air Bags fit into tight spaces where traditional jacks cannot, using compressed air to lift, move, or shift heavy loads with precise control. Ideal for shifted containers, machinery, and other heavy loads that need to be moved quickly.
Plugs, wedges and a mallet.
The oldest answer to a leak is still the fastest. Tapered softwood plugs and wedges, heat treated so they drive clean and swell tight, for hull penetrations, pipe ruptures, sea chests and fuel lines.
- Kits from the 16 piece grab bag to the 104 piece MAXIWEDGE
- Hardwood, softwood and neoprene options
- Heat treated to 56°C core for a minimum of 30 minutes
Marine Plug & Wedge Kit Options
Hazardous and vapor control
For fuel and chemical service the TP715 adds neoprene plugs for vapor control and a non-sparking AMPCO mallet. Its neoprene plugs are molded to accept extension handles and powered impact tools, so you can seat a plug you cannot safely reach by hand.
Eyes for the night. And the smoke.
One line covers the whole thermal picture on board: M-Series pan and tilt cameras for navigation and man overboard, handheld Ocean Scouts for the deck bag and K-Series cameras for the fire below decks.
- M-Series multispectral pan and tilt for navigation and search
- Handheld Ocean Scout cameras for the deck bag
- K-Series cameras for shipboard firefighting
Fixed mount: M-Series
Note: The MD-Series Cameras do not pan or tilt.
Refresh Rate: 9Hz
FOV: 24° x 18°
JCU Match: JCU3 or JCU4Learn More →
Refresh Rate: 9Hz
FOV: 63.7° × 35.8° wide → 2.3° × 1.29° narrow
JCU Match: JCU4Learn More →
Refresh Rate: 9 Hz or 30 Hz
FOV: 24° x 18°
JCU Match: JCU4Learn More →
Refresh Rate: 9 Hz or 30 Hz
FOV: 24° x 18°
JCU Match: JCU4Learn More →
Visible Resolution: 1920 x 1080
Refresh Rate: 9 Hz or 30 Hz
FOV: 24° x 18°
JCU Match: JCU4Learn More →
Visible Resolution: 1920 x 1080
Refresh Rate: 30Hz
FOV: 24° x 18°
JCU Match: JCU4Learn More →
Visible Resolution: 1920 x 1080
Refresh Rate: 9 Hz or 30 Hz
FOV: 24° → 6° HFOV
JCU Match: JCU4Learn More →
Visible Resolution: 3840 × 2160 (4K)
Refresh Rate: 30Hz
FOV: 30.68° → 5.86°
JCU Match: JCU4Learn More →
Visible Resolution: 1920 x 1080
Refresh Rate: 30 Hz NTSC / 25 Hz PAL
FOV: 28° × 21° wide → 2° × 1.5° narrow
JCU Match: JCU4Learn More →
Visible Resolution: 3840 × 2160 (4K)
Refresh Rate: 30Hz
FOV: 1.9°–2.8°*
JCU Match: JCU4Learn More →
Matching JCU control units are sold separately.
M-Series Accessories
Handheld: Ocean Scout
FOV: 32°
Focal Length: 19 mm
Focus: Fixed Focus
Human Detection: 500 m (540 yards)Learn More →
FOV: 18°
Focal Length: 35 mm
Focus: Manual Focus
Human Detection: 1000 m (1100 yards)Learn More →
K-Series for the fire below
- Resolution: 640 x 480
- Display Frequency: 60Hz
- FOV: 94° x 74°
- Wifi Connectivity Available
- Resolution: 640 x 480
- Display Frequency: 60Hz
- FOV: 53° x 40°
- Wifi Connectivity Available
- Resolution: 640 x 480
- Display Frequency: 60Hz
- FOV: 53° x 40°
- Wifi Connectivity Available
- Resolution: 320 x 240
- Display Frequency: 60Hz
- FOV: 53° x 40°
- Wifi Connectivity Available
- Resolution: 240 x 180
- Display Frequency: 30Hz
- FOV: 51° x 38°
- No Wifi Connectivity Available
- Resolution: 160 x 120
- Refresh Rate: 9Hz
- FOV: 47° x 35°
- No Wifi Connectivity Available
IP67 rated and drop tested from 2 meters, which matters more at sea than anywhere else.
A voice where radios fail.
Steel hulls eat radio signal. RESCOM Elite hard-line kits put a wired, powered voice loop between the entrant, the attendant and the team, in engine rooms, voids, tanks and every below-deck space where a handheld is a liability.
- Elite kits sized for 2, 3, 5 or 7 crew
- DuraCORE communication cable, or communication rope
- Junction boxes scale the loop as the team grows
RESCOM Kit Options
Each Elite kit pairs a DMI-E master station with DSI-E crew stations, with a 100 ft or 300 ft cable or rope.
Note: Headsets can be changed upon request.
(1) 100' or 300' Communication Cable or rope
(1) DMI-E
(1) DSI-E
(1) Master headset
(1) Crew Headsets (watertight w/ throat mic)
(1) Small Rope Bag
(1) Medium Equip. Case
(2) 100' or 300' Communication Cable or rope
(1) 50' DuraCORE Cable
(1) DMI-E
(2) DSI-E
(1) Master headset
(2) Crew Headsets (watertight w/ throat mic)
(1) 4 port Junction Box
(1) Medium Equipment Case
(4) 100' or 300' Communication Cable or rope
(1) 50' DuraCORE Cable
(1) DMI-E
(4) DSI-E
(1) Master headset
(4) Crew Headsets (watertight w/ throat mic)
(1) 6 port Junction Box
(1) Large Equipment Case
(6) 100' or 300' Communication Cable or rope
(1) 50' DuraCORE Cable
(1) DMI-E
(6) DSI-E
(1) Master headset
(6) Crew Headsets (watertight w/ throat mic)
(1) 8 port Junction Box
(1) Large Equipment Case
Kits can be built based on the size and needs of your crew.
Cable or rope: which one?
Rope color options are available: yellow (standard), blue, green, orange, purple and red.
Chain, hook and hold.
Grade 70, 80 and 100 chain packages for deck rigging, recovery and securing a load that has shifted, with griphoists for the pulls you need to control by the inch.
- TRC570 general duty and TRC-6K heavy duty packages
- Grade 80 and 100 assemblies built to spec, 4:1 safety factor
- Griphoists in 1, 2 and 4 ton capacities, as a kit or individually
Chain Package & Accessory Options
(1) 1-1/2 Ton Capacity Chain Come-A-Long
(1) Anchor Chain
(1) Pulling Chain
(1) Loading Hook
(1) Cheater Chains
(1) Carrying Container.
(1) 3 Ton Capacity Chain Come-A-Long
(1) Adjustable Single Chain Sling
(1) 1-1/2 Ton Capacity Chain Come-A-Long
(1) Pulling Chain
(1) Cheater Chain
(1) Loading Hook
(1) J-Type Recovery Hook.
One spark is all it takes.
Fuel vapors, cargo dust and confined tanks do not forgive an ordinary steel tool. AMPCO aluminum bronze tools are spark resistant, non-magnetic and corrosion resistant, and TEAM builds them into cased kits ready for the DC locker.
- Spark resistant, non-magnetic, corrosion resistant
- Cased kits from 6 to 30 tools
- The right mallet for every plug and wedge kit
Kit Options
- Bar Crow 24" OAL
- Chisel Hand 7/8", 9" OAL
- Pin Straight 1/4 Tip 6" OAL
- Hammer Claw 1.25 Lb 14" OAL
- Knife Common 3-1/8" Blade
- Knife Putty 2" Stiff Blade
- Mallet 4Lb 15" OAL
- Pliers Adj Combination 8" OAL
- Pliers Groove Joint 10" OAL
- Pliers Lineman's 8-1/2" OAL
- Pliers Needle-Nose 7" OAL
- Scaper Deck 2" Blade 12" OAL
- Screwdriver Std 5/16 x 3"
- Screwdriver Std 5/16 x 6"
- Screwdriver Std 3/8 x 8"
- Screwdriver Phillips #1
- Screwdriver Phillips #2
- Screwdriver Phillips #3
- Wrench Adjustable 8" OAL
- Wrench Adjustable 12" OAL
- Wrench Combination 3/8"
- Wrench Combination 7/16"
- Wrench Combination 1/2"
- Wrench Combination 9/16"
- Wrench Combination 5/8"
- Wrench Combination 11/16"
- Wrench Combination 3/4"
- Wrench Combination 7/8"
- Wrench Bung for 21 Bungs
- Wrench Pipe Bronze 14" OAL
- SOFT CARRYING CASE
- Bar Crow 18" OAL
- Hammer Claw 1.25 Lb 14" OAL
- Knife Common 3-1/8" Blade
- Knife Putty 2" Stiff Blade
- Pliers Adj Combination 8" OAL
- Pliers Groove Joint 12" OAL
- Pliers Lineman's 8-1/2" OAL
- Scaper Deck 2" Blade 12" OAL
- Screwdriver Std 5/16 x 6"
- Screwdriver Phillips #2
- Wrench Adjustable 8" OAL
- Wrench Dbl Box 5/16x3/8"
- Wrench Dbl Box 7/16x1/2"
- Wrench Dbl Box 9/16x5/8"
- Wrench Dbl Box 11/16x25/32"
- Wrench Dbl Box 3/4x7/8"
- Wrench Pipe Bronze 14" OAL
- SOFT CARRYING CASE
- SHOE BRUSH HANDLE
- 9" CRATE OPENER
- 16 OZ. CLAW HAMMER W/FIBERGLAS HANDLE
- COMMON KNIFE; 5-3/4" BLADE, 10-3/4" OAL
- PUTTY KNIFE (STIFF) 1-1/4" x 3-9/16" BLADE 7-3/4" OAL
- 12" GROOVE JOINT PLIER
- 7"LONG- NOSE PLIERS W/CUTTER
- 8" COMBINATION PLIERS
- DECK SCRAPER, 1-1/2" BLADE x 15" LONG
- SPRAY BOOTH SCRAPER, 3" BLADE x 9-1/4" LONG
- STD. SCREWDRIVER- 5/16" TIP, 6" BLADE
- #3 PHILLIPS SCREWDRIVER
- 12" TIN SNIPS
- 8" ADJ. WRENCH
- 12" ADJ. WRENCH
- 14" PIPE WRENCH (ALUMINUM)
- 12" BUNG WRENCH
- Bucket & Screw Top
- 9" OPENER
- 6 1/2" COMBINATION PLIERS
- 9 1/2", 1 1/2" CAP.GROOVE JOINT PLIERS
- STANDARD SCREWDRIVER 3" BLADE
- #2 PHILLIPS SCREWDRIVER
- 8" LENGTH, 15/16" CAP. ADJ. VINAL CASE WRENCH
- SOFT CARRYING POUCH
- SHOE BRUSH HANDLE
- 16 OZ. CLAW HAMMER W/FIBERGLAS HANDLE
- COMMON KNIFE; 5-3/4" BLADE, 10-3/4" OAL
- PUTTY KNIFE (STIFF) 1-1/4" x 3-9/16" BLADE 7-3/4" OAL
- 8" COMBINATION PLIERS
- STD. SCREWDRIVER- 5/16" TIP, 6" BLADE
- 10" GROOVE JOINT PLIERS
- #2 PHILLIP SCREWDRIVER
- 6" ADJ. WRENCH
- 10" ADJ. WRENCH
- 10" ADJ. PIPE WRENCH
- CARRYING CASE
Plan your DC lockers.
Tell us the vessel and the class requirement, and we will build the damage control package around it.